upvote
The latest Chamberlain openers (Chamberlain Security+ 3.0) don't work with this. There is no wired connection to operate the door, and the wireless operation is completely locked down.
reply
I would bet that there are connectors/test points on the board inside that would be reasonably easy to hook into. Naturally, that is a bit more involved than just hooking up a wire, but still not an insurmountable obstacle if one is already trying to do something like this.
reply
Normally, I'd agree but they are well aware of both software and devices attempting to work around their cloud lockdown and very aggressively trying to block any local control.

It's also important to understand they are backed by a private equity firm spending a lot money buying up the other leading garage door companies. This isn't just a preference to keep people in their cloud if possible, it's a long-term plan to corner the market and distribution channels and then start locking all remote features behind $ubscription pay walls and all their non-Chamberlain brands will do it too.

They've already shown they're willing to increase BOM costs on stuff that only locks out local-only use.

reply
Looks like the perfect time for a disruption of that business model.
reply
My thoughts exactly. Worst case, you get bought out by them.
reply
So as usual all you need to know is "purchased by private equity" the amount of times this results in anything other than enshittification is probably less than 0.1%
reply
There are other garage door openers, just use those at that point
reply
Could be, but also since the opening is exclusively controlled by software, they may not have any need for such connectors. I would check, but they're not particularly easy to poke around once they are installed.
reply
But like, there’s still a physical button on the remote, right? Why can’t you just solder a couple wires to the button on the remote?
reply
You can, but that by itself does not give you the garage door state (open or closed), just a blind toggle.
reply
I used a Meross device in our old home that came with sensors to install and detect the door state. If I remember correctly, the connection between the device and the opener was through a wireless remote that we paired with the opener like any other remote.
reply
It's easy to get the garage door state with a sensor: https://ratcloud.llc/products/ratgdo-encoder
reply
I have this even cheaper/simpler Zigbee tilt sensor that just sticks to your garage door. $12 on Amazon: https://www.amazon.com/dp/B0CZP2CJXF?plpRedirect=mhFallback&...
reply
Can you use a paired wireless remote paired with an open interface that closes the necessary contacts on the remote?
reply
I tried this with mine. I had a homekit garage door thing that had worked at my old house, and figured I could have it just push the button on a wireless remote paired to my new garage door opener, so I ordered this a generic garage door opener with the button contacts broken out. That would not pair with my stupid myQ garage door opener. I got a radgdo and it works like a Swiss watch. I love whoever got mad enough to get PCBs made for it. It's a great piece of technology in my house.
reply
That's what I ended up doing, this thingy physically presses the button: https://www.thirdreality.com/products/smart-garage-door-open...
reply
This is how I have been opening and closing my garage door for the last 10 years.

One of these:

https://www.insteon.com/products/io-module-garage-door-contr...

...with the contact closure wires soldered to the button of a car remote.

Controlled by Universal Devices isy994i/eisy.

I do have to change the battery in the remote every five to six years or so.

reply
It's just a matter of time though right. Claude, bruteforce this protocol!
reply
I hope so!
reply
> It's just a matter of time

..before they stop allowing this, especially after IPO

reply
DeepSeek 1017 and GLM 5.3 may be the best open models we ever get, because even the Chinese are slamming the door on reverse engineering at this point.

But fortunately those two models are good enough to do stuff like this.

reply
> because even the Chinese are slamming the door on reverse engineering at this point.

The future of reverse engineering is abliterated models running on your own or rented hardware.

reply
The original post and your comment made me discover this and now reading about

  The ratgdo encoder is a precision sensor that tracks your garage door's physical state. It enables your ratgdo control board to detect the door's exact position and direction of travel in real time—whether it's fully open, closed, or anywhere in between.
I feel dumb implementing my own "sliding door open/closed/in-between" sensor with 2 cheap zigbee door sensors and some logic in Home Assistant
reply
Would love to know how easy this was and how well it works with HA.
reply
Great for me, I had mine all set up in HA with an older overhead Chamberlin opener, and then had that replaced with a jackshaft opener. I had to reflash the Ratgdo (for the new security protocol) but it wasn't any harder to set up once I did that, now it's working perfectly once again.
reply
Incredibly easy. Connection is a couple of wires, no soldering.

Home Assistant integration is flawless. There is esphome firmware for the ratgdo (instructions in their official docs) and if you're familiar with esphome, you know how well it works with HA. Very low latency and 100% local.

It also allows me to setup useful automations like locking all remotes at night so if someone breaks in my car, they can't hit the button to open the garage.

reply
I will second the use of RATGDO for these Chamberlain openers. Easy to set up and works flawlessly. Have one on an older opener and one on a RJO101.
reply
Hardest part was installing it while on a ladder, but it was pretty simple from what I remember.
reply
It's been working flawlessly for me with HA for years now.
reply
deleted
reply
Knowing companies like Chamberlain, hopefully they don’t start legally bullying ratgdo with things like “patent infringement”
reply
This is a fantastic product, but man, do tech people have trouble with branding. "Is it Rat Guh-do? Rat-du with a silent g?". It's almost as bad as naming everything "yet another...".

Maybe call it "How I learned to stop worrying and love the garage door opener" or "HILTS-WALT-GDO" for that extra eye-rollingness.

reply